A: I'm sure it could with the correct blade, but it's a toilet, gently use a sledge hammer to break the bowl into several pieces. Much quicker, much less dust, much easier.
Or do you men to use it to cut through the rusted bolts that hold the toilet to the floor? If so, it'll do it in a few seconds with the metal-cutting blade and then lift off the whole toilet.
by|May 4, 2023
A: no the fastest way to destroy a toilet bowl and tank are a sledge hammer.
by|Mar 26, 2021
1 found this answer helpful
A: No. You would need a grinder or a cut off wheel on a Whizzer. The blades on a Sawzall are not designed to cut through porcelain.
by|May 4, 2023
1 found this answer helpful
Q:Does it variable spped, pivot or fixed shoe, and 4 position blades
by|Jun 17, 2017
2 Answers
Answer This Question
A: It is variable speed and the shoe pivots and can be removed. Blades can be inserted facing forward or backward.
by|May 4, 2023
1 found this answer helpful
A: Not variable speed, pivot shoe and I'm not sure exactly what you are mean about the 4 position blades.
by|May 4, 2023
Q:does it have a keyless chuck
by|May 13, 2017
5 Answers
Answer This Question
A: Twist and release blade lock
by|May 5, 2023
A: Yes it does. The chuck is built in.
by|May 4, 2023
A: Yes, this saw has a QUIK-LOK blade clamp for tool-less blade changes.
by|May 4, 2023
A: Yes
by|May 4, 2023
A: Yes
by|May 6, 2023
Q:We have rented one,finding it hard to put blades in
by|May 10, 2017
3 Answers
Answer This Question
A: Must have been something wrong with the one you rented, blade change on mine is extremely simple.
by|May 30, 2019
A: The little 'cap' end of the saw where the blade slips into twists to the left. Just twist it, hold it in that position and slip in the blade, and release it. It's spring-loaded and will lock itself closed. That's all there is to it.
by|May 4, 2023
2 found this answer helpful
A: stand on end, put thumb and one or two fingers around ribbed knob where blades go push down put blade in it will drop if you have the knob all the way down
by|May 4, 2023
Q:Are the brushes in a12 amp Milwaukee sawzall able to be replaced by myself or does a service shop have to do it
by|Mar 28, 2017
2 Answers
Answer This Question
A: You can replace them yourself after disassembling the handle (7 screws). However, notice that they are held only by plastic housing. When my brushes failed, they melted the plastic handle and the gray motor housing around them. So open the handle and take a look. If the plastic is melted around the brushes, it's time for a new saw. Also, check the armature segments carefully - they may be falling apart already.
by|Nov 8, 2018
A: The owner's manual says to take the saw to a service center for brush replacement.
by|May 4, 2023
Q:Does this saw have and orbital cutting action?
by|Jan 31, 2017
5 Answers
Answer This Question
A: Nope. Just back and forth.
by|May 4, 2023
A: this is not orbital.
by|May 5, 2023
A: No..not an orbital
by|May 5, 2023
A: No, not this particular model.
by|May 4, 2023
A: no just straight line
by|May 4, 2023
Q:where was the saw made?
by|Dec 13, 2016
2 Answers
Answer This Question
A: The tag on the saw says "Assembled in the USA with some foreign components."
by|Mar 3, 2021
1 found this answer helpful
A: mine says assembled in USA with domestic and foreign parts
by|Mar 3, 2021
1 found this answer helpful
Q:Is there some one for 220 volts or all of them are for 110 volts?
by|Nov 30, 2016
2 Answers
Answer This Question
A: this one is 110
by|May 4, 2023
A: I only see 110 volts hand power tools at Home Depot, and have never seen this type of tool for 220 volts outlets.
by|May 4, 2023
1 found this answer helpful
Q:is the cord removable ?
by|Oct 30, 2016
3 Answers
Answer This Question
A: The cord is not removable.
by|May 4, 2023
1 found this answer helpful
A: No, this model does not feature the Milwaukee Quik-Lok cord.
by|May 4, 2023
1 found this answer helpful
A: If you took the cord off it would not work needs power
by|May 4, 2023
Q:Big posts. From what I read the blade and tool isn't designed to make that big of cut. If not this one what do you recommend?
by|Sep 25, 2016
3 Answers
Answer This Question
A: Hmm, surprising feedback you have received. I did buy an assortment of blades (stock ones are notoriously considered underperformers). Length is important as will be teeth spacing. If you can afford a larger, heavier, more powerful unit, then do it. I cut dense bamboo and pine 2x4s with mine. Never at a lost for power. But you never know unless you try. If I were going to cut several 4x6 posts, I would not op for the smallest unit.
by|May 4, 2023
A: I wouldn't recommend it for heavy duty job like that. It's a light duty, homeowner saw.
by|Nov 8, 2018
A: Just get the correct blade and you'll have no problem. A new blade will cut those posts like butter. Don't force it, just let the saw do its job.